EUFY BoostIQ RoboVac 11S Vacuum Cleaner Manual

The EUFY BoostIQ RoboVac 11S is a powerful robotic vacuum cleaner designed to provide a hassle-free cleaning experience. With its slim design, it can easily navigate under furniture and reach tight spaces. The BoostIQ technology automatically increases suction power when extra strength is needed, ensuring a thorough clean on various floor types, including hardwood, tile, and carpet. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Operating the Vacuum 8. Maintenance 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Slim design, BoostIQ technology, multiple cleaning modes, anti-collision sensors, and a large dustbin.

Feature	Description
Suction Power	Up to 1300Pa for deep cleaning
Battery Life	Up to 100 minutes of continuous cleaning
Dustbin Capacity	0.6L for less frequent emptying
Noise Level	Quiet operation at 55dB
Remote Control	Convenient control from a distance
Smart Navigation	Efficient cleaning path with anti-collision sensors
Multiple Cleaning Modes	Auto, Spot, Edge, and Max modes

Installation

Unpack and inspect contents. Place RoboVac on a flat surface for charging.

Connect the charging dock to a power outlet.
Ensure the RoboVac is fully charged before first use.
Remove any obstacles from the cleaning area.

WARNING! Keep the charging dock away from water and moisture.

First-Time Setup

Power on the RoboVac; follow the instructions on the remote control.

Press the power button to turn on the RoboVac.
Use the remote to select cleaning modes.
Set a cleaning schedule if desired.

CAUTION! Ensure the dustbin is empty before operation.

Specifications

Model: EUFY BoostIQ RoboVac 11S
Suction Power: 1300Pa
Battery Type: Lithium-ion
Battery Capacity: 2600mAh
Charging Time: 5-6 hours
Dimensions: 12.8 x 12.8 x 2.85 inches
Weight: 5.73 lbs
Noise Level: 55dB

Controls and Settings

Access controls via the remote or the RoboVac itself. Use the remote for scheduling and mode selection.

Cleaning Modes: Auto, Edge, Spot, and Max.

Settings include scheduling, suction power adjustment, and cleaning mode selection.

Connecting Devices

RoboVac does not require additional devices for operation. Ensure the charging dock is connected to a power source.

Place RoboVac on the charging dock when not in use.
Ensure the dock is plugged in and the indicator light is on.

Tip: Keep the charging area clear of obstacles.

Operating the Vacuum

To start cleaning, press the power button or use the remote control.

Press the AUTO button for standard cleaning.
Use the SPOT mode for concentrated cleaning in a specific area.
Press the EDGE button for cleaning along walls and corners.

WARNING! Do not block the sensors during operation.

Maintenance

Regular maintenance is essential for optimal performance.

Empty the dustbin after each use.
Clean the filters every month.
Check the brushes for hair or debris and clean as needed.

CAUTION! Always turn off the RoboVac before performing maintenance.

Regulatory Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Troubleshooting

Symptom	Possible Cause	Corrective Action
RoboVac not charging	Dock not plugged in	Ensure dock is connected to power
No suction	Clogged filter	Clean or replace the filter
RoboVac not moving	Obstruction detected	Clear the path and restart
Remote not working	Dead batteries	Replace batteries in the remote

Reset: Press the reset button if available.

Service: For support, contact EUFY customer service.